Jyoti Power Tools & Hardware

LATICRETE® 307 floor and wall tile adhesive is a smooth and creamy thin-set Adhesive for installing small to medium format ceramic wall and floor tiles in interior areas. For improved performance and exterior use, fortify with LATICRETE® 73 Crete Admix.

• For fixing ceramic tiles on interior floor & wall
• Ideal for new floor tiling
• Smooth & Creamy
• Single component - Just add water

• If a plaster/leveling mortar bed is applied, ensure that it is cured for at least 7 days to achieve proper strength before application of tile adhesive for installation of tile
• Ensure the substrate is clean and free from impurities like dust, dirt, debris, oil, grease, curing agents, loose plaster etc
• Dampen the wall before application of thin set adhesive
• Clean the back of tile for any dust or coating

• Wet the surface and remove the excess water before applying the adhesive. Ensure the area is shaded from sunlight. The adhesive shall be applied with the flat side of the trowel using a scraping motion to work the material into good contact with the surface to be covered.
• Additional mortar is then applied with the notched edge of the trowel.
• When installing large tiles, spread adhesive onto the back of tile in addition to trowelling material over a surface to be tiled. Select proper type of notched trowel.

a) Thin Tiles upto size 300 X 300 mm (1’X1’), use a square notched trowel of size 6mm X 6mm to provide a total thickness of 3mm

b) Large Porcelain Tiles upto 450 X 450 mm with ribs, use a square notched trowel of size 6mm X 6mm and back butter the tiles with the same adhesive to a thickness of 1-1.5mm to provide a total thickness of 4.5mm

c) Large Porcelain Tiles upto 600 X 600 mm (2’X2’) with ribs, use a square notched trowel of size 6mm X 9mm and back butter the tiles with the same adhesive to a thickness of 1-1.5mm to provide a total thickness of 6mm

• The most important standard to keep in mind is to insure that the piece of tile is completely bedded in the mortar or adhesive with 100% coverage.
• Rear face of tiles (especially Porcelain tiles) should be cleaned with damp sponge to clean all the dust. Do not saturate in water.
• Excess mortar on adhesive shall be cleaned from the surface of the stone with wet cloth or sponge while the mortar is fresh.

• Cement Mortar Beds
• Existing tiling on floor & wall Ceramic Tile and Stones (when mixed with LATICRETE® 73 Mortar Admixture)
• Cement Plaster
• Brick Masonry
• Terrazzo

Roff Extrofix Adhesive is a highly polymer-modified glue used to fix all types of tiles, ceramics, marble, and natural stones on external and internal surfaces. It is predominantly used as tile/ natural stone/ ceramic adhesive for external walls and floors. This low-VOC glue is ideal for fixing regular-size tiles in wet as well as dry surfaces in commercial areas. Roff Extrofix Adhesive gives high adhesion and ensures that the tile is glued to the concrete. You can use this product for fixing purposes in commercial and domestic areas. The product is also formulated to act as a superior bonding agent and absorbs external shocks in high-traffic areas.

It Is Highly Convenient To Use This Product. The Mixture Can Be Easily Prepared On The Site By Adding The Required Amount Of Water. The Mixture Is Applied In Small Sections To Achieve Precision While Fixing The Tiles.

It Is Used For Adhesion On External Surfaces As It Has A Long Open Time. This Product Can Fix Tile/ Natural Stone/ Marble/ Ceramic In Outdoor Areas. It Is Extremely Suitable For Larger Formats.

It Is A Highly Polymer-modified Glue That Forms A Strong Bond With The Substrate At The Time Of Application.

It Can Sustain Minor Vibration On The Surface As It Is A Flexible Adhesive.

Roff Extrofix Adhesive Is Shock And Water-resistant Making It Suitable For Application On Wet Surfaces. This Adhesive Can Withstand Heat Ageing, Making It Fit For Use In High-temperature Areas Such As Jacuzzis, Outdoor Spaces, And Saunas.

This Glue Is Also Used On Vertical Surfaces Due To Its Sag-resistant Feature.

Material To Be Fixed: Roff Extrofix Adhesive Can Be Used On All Kinds Of Ceramic Tiles, Natural Stones, Marbles, Large Format Tiles, And Low-thickness Slabs In External Areas.

On Surface/substrate: It Acts As A Bonding Agent And Is Applied On Cement-based Beds, Gypsum, Waterproofing Products, Drywall Like Cement /bison/ Gypsum Boards*and Other Surfaces To Fix Tiles.

Area Of Application: The Area Of Application Of Roff Extrofix Adhesive Is Wet As Well As Dry Surfaces In Outdoor And Indoor Spaces. The Product Can Be Used In Household And Commercial Projects On Horizontal And Vertical Surfaces For Gluing Tiles.

The Surface On Which The Adhesive Is To Be Applied Must Be Evened Out And Should Be Free From Any Debonding Agent. It Ensures Proper Adhesive Contact And Strong Gluing Of The Tiles.

It Is Important To Dampen Any Dry Surface Prior To Mixture Application.

Any New Concrete Should Be Properly Damped And Left For At Least A Month Before Applying The Adhesive. This Minimizes Shrinkage On The Application Surface.

The Expansion Joints Should Be Grouted With A Suitable Product Before The Application Of Adhesive.

The Tiles Should Be Fixed Within Half An Hour Of Adhesive Application, Depending On The Surface Porosity And Atmospheric Condition.

Roff Extrofix Adhesive Comes In A 20 Kg Packet Which Is Economically Priced And Works Well For Fixing Tiles On External Surfaces.

Description:- High polymer modified adhesive for fixing tiles and natural stone on interior and exterior floor & wall.
Features:-
Single component, just add water
High strength, polymer modified
Economical & Easy to use
Bonds to various substrates
Exceeds ANSI A118.4 shear bond strength requirements
Complies with EN / ISO with a C2TE classification.
Exceeds IS 15477:2019 – Type3 T Adhesive standards.
Water and shock resistant.
Premium adhesive for shear wall
Formulated for shear wall and low absorbent cementitious substrate
Can be used upto a bed thickness of 15 mm
High bond strength & resistant against shrinkage crakes
Single component just add water
Do not use hand hooks
Keep dry
Keep away from direct sunlight

Description:- Polymer based adhesive for fixing ceramic tiles and small format natural stone on dry areas of interior floor & interior wall up to a height of 3 Mtrs.

Features:-

Single component, just add water

High strength, polymer modified

Economical & Easy to use

Bonds to various substrates

Exceeds ANSI A118.4 shear bond strength requirements

Complies with EN / ISO with a C2TES1 classification.

Exceeds IS 15477:2019 – Type 3 TS1 Adhesive standards.

Water and shock resistant.

Multipurpose floor and wall tile adhesive

For fixing tiles & stone on demanding external & internal applications

Polymar modified super flexible adhesive with superior bond strength

High performance in all type of weather

Single component just add water

Do not use hand hooks

Keep dry

Keep away from direct sunlight

Substrates:-

Concrete & Concrete Masonry

MIVON Concrete, VDF, Tremix Concrete

Cement Mortar Beds

Cement Plaster

Ceramic tile, Vitrified Tile and Natural Stone

Glass mosaic tile

Brick Masonry

Cement Backer Board

Cement Terrazzo

Calcium Silicate Board

Gypsum Wallboard

• Floors and walls, for internal and external use
• Open and adjustability time ≥ 30 min.
• Suitable for vitrified tiles, ceramics, large formats, low thickness slabs and natural stone
• Ideal for marble and natural stone that tends to form stains and sag in the presence of humidity
• Ideal for resin‑based engineered stones
• Easy and light to spread thanks to the Light Work technology
• Elastic Polyurethane Organic Mineral Adhesive For Higher Performance And High Adhesion Fixing With No Vertical Slip On Deformable Surface 
• Seal For Use In Green Building  
• Suitable For Porcelain Tiles , Ceramics, Large Formuales , Low Thickness Slabs and Natural Stone 

• Polymer‑Modified
• Ideal for Walls
• Ideal for Wet Areas
• Adhesive For Fixing Ceramic Tiles Indoor And Outdoor Areas And Vitrified Tiles Only Indoor.
• Ideal For Fixing On Internal Walls
• Polymer Modified Adhesive
• No Vertical Slip
• Thickness Of Adhesive Up To 15 Mm
• Ideal For Internal Wet Areas
• Ideal On Kerakoll Mineral Waterproofing Membranes

Roff T05 Tile Adhesive is a high-performance adhesive specially developed for tile fixing applications. It is primarily used for bonding ceramic tiles, vitrified tiles, and natural stone tiles to different surfaces, including floors and walls.

Roff T02 Tile Adhesive is a high-quality adhesive specifically formulated for tile installation applications. It is primarily used for fixing ceramic tiles, vitrified tiles, and natural stone tiles onto various surfaces, including floors and walls.

We are engaged in offering Roff T08 Etrofix to our clients. Our range of all products is widely appreciated by our clients.

Roff T09 Tile Adhesive is a premium-quality adhesive specifically designed for tile installations. Manufactured by Roff, a trusted brand in the construction industry, this adhesive offers superior performance and reliability.

We are engaged in offering Roff T03 Grey to our clients. Our range of all products is widely appreciated by our clients.

MYK Laticrete 307 is a high-performance, polymer-modified, cementitious tile adhesive designed for fixing ceramic tiles, vitrified tiles, and natural stones on a variety of substrates. With excellent bond strength, smooth workability, and long open time, it ensures durable and secure tile installations for both interior and exterior applications.
Key Features:

High bonding strength for ceramic, vitrified, and natural stone tiles

Suitable for floor and wall applications

Easy to mix and apply with consistent coverage

Water and heat resistant, ideal for wet areas

We are engaged in offering Myk Laticrete Pua 212 to our clients. Our range of all products is widely appreciated by our clients.

Description:- High polymer modified adhesive for fixing tiles and natural stone on interior and exterior floor & wall.

Features:-

Single component, just add water

High strength, polymer modified

Economical & Easy to use

Bonds to various substrates

Exceeds ANSI A118.4 shear bond strength requirements

Complies with EN / ISO with a C2TE classification.

Exceeds IS 15477:2019 – Type3 T Adhesive standards.

Water and shock resistant.

Premium floor and wall tile adhesive

For fixing ceramic, verified tiles & natural stone on interior floor & wall

Ideal for life-on-tile & new floor tiling

High bond strength

Single component just add water

Do not use hand hooks

Keep dry

Keep away from direct sunlight

Substrates:-

Concrete & Concrete Masonry

VDF / Tremix Concrete

Cement Mortar Beds

Cement Plaster

Ceramic tile, Vitrified Tile and Natural Stone

Glass mosaic tile

Brick Masonry

Cement Backer Board

Cement Terrazzo

Calcium Silicate Board

Gypsum Wallboard

MYK Laticrete 315 is a high-performance, polymer-modified, cementitious tile adhesive designed for fixing ceramic tiles, vitrified tiles, and natural stones on a variety of substrates. With excellent bond strength, smooth workability, and long open time, it ensures durable and secure tile installations for both interior and exterior applications.

Key Features:

• High bonding strength for ceramic, vitrified, and natural stone tiles

• Suitable for floor and wall applications

• Easy to mix and apply with consistent coverage

• Water and heat resistant, ideal for wet areas

• Free Pen And Pocket Diary With
• High Strength 
• Bonds Multiple Substrates 
•  Solvent Free 
•  Clear & Transparent Bond
• Fast And Clear 
• 5min Epoxy Adhesive